Technical Information

You can also download a copy of our Technical Sheet here.

DESCRIPTION

Ecogranito offers revolutionary water-base coatings that replicate the look and feel of natural stone, formulated for exterior and interior use.

Our products are weather resistant and can be used with many Industry-Standard Integrated Structural Wall Systems and Barriers, such as ICF/EIFS.

Contact us if you have any questions on the suitability of our products for your specific project.

COMPOSITION

Water, acrylic resin and water base additives, pigments, coalescing, non-metallic microbicides, inert mineral and fillers.

COLOURS

As per catalogue.

FIRE RATING (ASTM E84 & CAN/ULC S-102)

Flame Spread Index: 5 (Class “A”)

Smoke Developed Index: 20 (Class “A”)

Smoke Developed Value: 17 (No performance criteria)

EXPIRY DATE

For optimal results, Ecogranito products should be used within 18 months from manufacturing date. 

Technical Department

1-855-GRANITO (1-855-472-6486) ext. 2 

Attention

WARNING

Do not dilute. Our products are ready to use. Mix well before application. 

Do not apply Ecogranito products on rainy days, when temperatures are below 10ºC (50ºF) or above 35ºC (95ºF), or when the humidity index is at or above 85%.

SAFETY INFORMATION

Wash hands thoroughly after handling. Wear protective gloves. In the event of product contact with skin or eyes, wash immediately with plenty of water for several minutes. If there is skin or eye irritation, respiratory changes, or ingestion, do not induce vomiting and seek medical attention. Keep product away from children. Dispose of contents/container in accordance with local regulations.

SITE CONDITION

Apply Ecogranito products only when ambient temperature is between 10ºC (50ºF) and 35ºC (95ºF) – temperatures must remain within this range for the next 24 hours after application. Do not apply if rain is expected within 48 hours of application.

SURFACE PREPARATION

The surface to be coated must be dry, clean, leveled, free from dust, grease, mold, rust, dirt, wax, chalk, mildew, efflorescence, and loosen or peeling paint. Remove loose paint/chalk by brushing, scraping and/or sanding. If applying on newly poured concrete, allow concrete to cure for a minimum of 28 days before using our products. If applying to substrates other than cement or concrete, additional surface preparation may be required. For further information, access our website or contact us.

Ecoprimo Primer 2-Coat Application

ATTENTION

  • Do not dilute. Product ready to use.
  • Stir well before use.
  • Apply two full coats (let it dry for at least 6 hours between coats)

TOOLS AND PPE NEEDED

  • Latex gloves
  • Flat paint brush and roller
  • OPTIONAL: Double-sided foam tape for “slab” marking

APPLICATION INSTRUCTIONS

  • Stir well before use. Apply the first coat of EcoPrimo using a flat roller or paint brush and let it dry for at least 6 hours.
  • Apply a second coat of EcoPrimo and let it dry for at least 12 hours.
  • OPTIONAL: After the second coat has fully dried for at least 12 hours, use a double-sided foam tape to design a “slab” layout marking in the shape and size of your preference to give you an even more natural stone appearance.

Ecogranno Finish Coat Application

ATTENTION

  • Do not dilute. Product ready to use.
  • Stir well before use.
  • Apply a thin single coat (between 2mm and 3mm thick maximum)

TOOLS AND PPE NEEDED

  • Latex gloves
  • Flat stainless-steel trowel
  • Container with clean water

APPLICATION INSTRUCTIONS

  • Stir well before use. Once the second coat of EcoPrimo has dried for at least 12 hours, apply a thin, single coat of Ecogranno using a flat trowel. This single coat should be not more than 2mm (less than 1/16 inch) thick.
  • Spread the product evenly across the surface. Do not make circular movements.
  • Do not apply a layer thicker than 2mm (1/16 inch), as this will result in fissures and smearing appearance.
  • Rinse the trowel in the container with cold water to avoid product from drying and sticking onto the tool. Use the cleaned and wet trowel to smooth the whole applied surface and remove any imperfections, until the desired look is reached.
  • Upon completing Ecogranno application and before the product dries, if the optional “slab” marking step was taken, remove the double-sided foam tape. Do not leave any tape after completing the application. This step will create the “grout look” of natural stone slabs.

Yield and Dry Time

AVERAGE YIELD – ECOPRIMO

  • Each EcoPrimo 25kg (55lbs) bucket yields, on average, 37 SqM or 400 SqFt.
  • Dry-to-touch: 6-12 hours

AVERAGE YIELD – ECOGRANNO

  • Each Ecogranno 25kg (55 lbs) bucket yields, on average, 5.6 SqM or 60 SqFt.
  • Dry-to-touch: 12-18 hours
  • Final drying: 2 to 5 days
  • Cure: 60 days

Maintenance and Cleaning

MAINTENANCE AND CLEANING

Ecogranito will last for years with minimum maintenance. In case it gets dirty for any reason, use neutral soap and warm water. Do not use pressure washer as it can affect product colour and its properties. Do not use other chemicals or bleach when cleaning.

STORAGE

Store Ecogranito products in dry, well-ventilated areas, with ambient temperature continuously maintained at not less than 5ºC (41ºF) or above 35ºC (95ºF). If there is product left after use, seal the plastic bag removing all the air, and cover the bucket using the original lid to prevent the product from drying out. ambient temperature continuously maintained at not less than 5ºC (41ºF). If there is product left after use, seal the plastic bag and cover the bucket using the original lid to prevent the product from drying out.

DISCLAIMER

Ecogranito products must be applied in accordance to specifications and application instructions. The architecture, design and engineering of projects using Ecogranito products are responsibility of the project’s design professional and must be approved and constructed pursuant to all applicable code requirements for that structure required at its jurisdiction. Our products can be applied as exterior or interior coatings on walls, ceilings, furniture, art objects, doors, among many others. Please contact us if you have any questions on the suitability of our products for your specific project. The applicator, contractor or professional applying Ecogranito products must consult the applicable code requirements for the jurisdiction in which the construction is commencing, not only to the application of Ecogranito, but also to the substrate upon which it is applied. Failure to adhere to those code requirements by the applicator could render the application deficient and nullify Ecogranito’s products warranty. The information and suggestions in this technical sheet for use contained herein are correct to the best of our knowledge and offered in good faith. The statements of this literature do not constitute a warranty, expressed, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials and does not include labour. All technical information is subject to change without notice.